Cement & Concrete Testing Equipment

NAME : Vibrating Table

Proper compaction of cement and concrete while casting specimens for compressive or flexural strength testing essential to achieve a better and more consistent mixture. The cement and concrete Vibrating Table top has stops along its edges to prevent moulds from sliding off the table during operation. The maximum load capacity is 140 kg. The concrete vibrating tables are offered in 3 different table top sizes:

NAME : Vibrating Machine

Proper compaction of cement and concrete while casting specimens for compressive or flexural strength testing essential to achieve a better and more consistent mixture. The cement and concrete Vibrating Table top has stops along its edges to prevent moulds from sliding off the table during operation. The maximum load capacity is 140 kg. The concrete vibrating tables are offered in 3 different table top sizes:

Cat No : AT-164
NAME : Mortar Cube Vibrating Machine
Quality Standard : As Per IS 4031, IS 10080

Mortar Cube Vibrating Machine is used for vibrating the mix in moulds at a frequency of 12,000 ± 400 cycles per minute. The vibrator is mounted over 4 coiled springs and the vibrations are developed by means of a revolving eccentric shaft. The centre of gravity of the vibrator, including the cube mould, is either at the centre of eccentric shaft or within 25 mm below it. The simple design of the machine facilitates easy assembly and dismantling of the cube moulds.

Cat No : AT-143
NAME : Slump Test Apparatus
Quality Standard : As Per IS 1199, IS 7320

The Slump Test Apparatus is filled with freshly mixed concrete and tamped with a tamping rod in three or four layers. The top of the concrete is leveled off with the top of the slump cone, the cone is lifted vertically up and the slump of the sample is immediately measured. The complete set comprises of a Steel Octagon Base Plate (8 faces) with carrying handle, Graduated Tamping Rod 16mm dia x 600mm long with one bullet end, slump cone having base 200mm, height 300mm fitted with handle.

Specification :

• Slump Cone Downside Diameter: 200 mm
• Slump Cone Tube Height: 300 mm
• Tamper: Dia 16 mm
• Material: Iron

Cat No : AT-143
NAME : Slump Cone Test Apparatus
Quality Standard : As Per IS 1199, IS 7320

The slump cone in these Slump Cone Test Apparatus is filled with freshly mixed concrete and stamped with a tamping rod in three or four layers. The top of the concrete is leveled off with the top of the slump cone, the cone is lifted vertically up and the slump of the sample is immediately measured.

Specification :

• Steel Octagon Base Plate (8 faces) with carrying handle
• Graduated Tamping Rod 16mm Dia x 600mm long with one bullet end
• Lump cone having base 200mm,
• Height 300mm fitted with handle
• Handle made of MS sheet

Cat No : AT-176
NAME : Laboratory Concrete Mixer

The Laboratory Concrete Mixer is used for preparing Mix Design of Concrete. It consists of a steel vessel of 55/ 110 Litres capacity, mounted on a frame. The vessel is rotated at 20-22 RPM with the help of a motor and a pulley arrangement. The vessel of laboratory concrete mixer can be titled to any angle by a hand wheel and counter weight. This facilitates mixing and discharge. Blades are provided inside the vessel to mix the material thoroughly. The large pulley wheel facilitates manual rotation of the drum during power failure. The drum, pulley wheel, and motor, etc, are mounted on a steel frame in these laboratory concrete mixer.

Specification :

• The concrete mixer is fitted with ½ HP motor
• Suitable for Operation on 260 V
• Phase: Single Phase, 50 Hz, AC Supply

Cat No : AT-186
NAME : Concrete Permeability Test Apparatus
Quality Standard : As Per IS 3085 / DIN Standard

The Concrete Permeability Test Apparatus is determined on cement, mortar and concrete specimens, either casted in the laboratory or obtained by cutting out cores from existing structures. Each cell of concrete permeability test apparatus is made of steel and provided with a top plate and funnel at the bottom having gasket seals held in position through bolts and nuts. Each test stall has its own control system, operating pressure gauges and valves. The multi-unit Permeameter are so designed that all tests can be performed at the same time using either the same head or varying head pressure as each test stall is provided with its own pressure regulator and control. The control instruments are mounted on a sturdy welded structural stand. All multi – units are provided with end pressure gauges. Each concrete permeability test apparatus is provided with chamber pressure gauges 0-20 kg/cm² and test pressure gauge of 0-15kg/cm². Pressures are applied using any available pressure line at the site or a 150PSI Electric Air Compressor. The Air Compressor is Suitable for operation on 220V, 1Ph, 50Hz AC Supply.

Specification :

NAME : Beam Moulds

Two standard sizes of Beam Moulds are offered for casting concrete specimens for flexural strength testing. These beam moulds are made of cast iron and are supplied complete with a base plate.

Specification :

• Material: S50 C
• Demoulding: Automatic
• Mould Life: <300000 shots
• Colour: Blue

NAME : Cylindrical Mould

Moulds for testing concrete Cylindrical Mould for Compressive Strength Testing are offered in two different sizes. These Cylindrical Mould are made of Cast Iron and split into two parts longitudinally. These are supplied complete with a base plate and top plate.

Specification :

• Minimum Order Quantity : 3 Piece
• Usage/Application : Industrial
• Packaging Type : Box
• Brand : Accro Tech
• Material: Tungsten Carbide,HSS etc
• Shaping Mode: Punching Mold
• Precision: ±0.002 mm
• Roundness: Within 0.0015 mm
• Concentricity: ±0.002 mm
• Straightness: Within 0.002 mm

NAME : Cube Mould

Four standard sizes of Cube Mould are offered and supplied complete with the base plate.

Specification :

• Cube Mould Size 15x15x15 cm
• Made of cast iron complete with base plate size 15x15 cm
• Cube mould made of cast iron complete with base plate size 15x15 cm

NAME : 150 Mm Four Part Cube Mould

Specification :

• Size : 150 x 150 x 150 mm
• Material : Cast iron
• Shape : Square
• Weight : 15 kg - 17 kg
• Design : Unique four part design
• Cast Iron construction, Unique four part design.
• Easy to use and clean